10L cheap pressure keg recommendation

[MashBag]

Trillions are very good, they easily make stuff you cannot buy that's a funny shape. Together with milliput and araldite hold most of my stuff together


Looking forward to the update.

[floydmeddler]

Check these out.
https://youtu.be/KTks6fZHQHI

https://www.kegland.com.au/8l-oxebar-mo ... h-cap.html

[MashBag]

Although I am not a fan of plastic (many reasons) I do get where they are coming from with this.

That said I cannot find a UK supplier?

[clarets7]

Check these out.
https://youtu.be/KTks6fZHQHI

https://www.kegland.com.au/8l-oxebar-mo ... h-cap.html

I'd looked at those as well, but as Mashbag says no UK suppliers that I could find.

[Cobnut]

They are available on aliexpress, but shipping rates are utterly ludicrous! Won't be buying atm.

[clarets7]

They are available on aliexpress, but shipping rates are utterly ludicrous! Won't be buying atm.

I see The Malt Miller is listed as a KegLand distributor - maybe if enough people show interest...

[floydmeddler]

Right... corny posts have arrived from China. Pretty quick!

Have run into a problem that I was fully expecting. Drilled two holes on top of the keg. Posts are in. However, I can't tighten them as the whole thing turns. Obviously can't get a spanner in there to hold the nut while I tighten it from the outside. Any ideas? Is there a such thing as a nut that will grip onto a surface? Something like this perhaps? Although I'd prob struggle to get them in the size I need...

https://image.made-in-china.com/202f0j0 ... ip-Nut.jpg

I don't want to use any silicone or rubber washers as the posts will just come loose when removing the disconnects. Have had this problem before with my DIY pressure fermenter. Was a nightmare. I ended up tightening the nuts within a mm of their life and they've stayed in place since. Was easy to do as they are on the lid. Would like to do that here. Help!

[floydmeddler]

Update. I used a bit of Gorilla weld on the inside nut. Just made everything hand tight to create a bond between the nut and the keg. Don't think Gorilla Weld bonds well to polyethylene but worth a shot. Watch this space!

[floydmeddler]

No joy. However, have just discovered the world of locking washers. Will look into that.

[floydmeddler]

Right... settled on wing nuts. Should be able to grip those between 2 fingers inside the keg while turning the outside nut with a spanner. Hopefully I've ordered the right size. Went for M12.

[MashBag]

The only thing I came with initially was kid with small hands, but they have made that illegal now, so won't mention it.

Perhaps a spring washer or a grippy nut.

https://www.ebay.co.uk/itm/183596380052 ... media=COPY

[MashBag]

.. Also available in stainless

[floydmeddler]

Cheers Mash. I had looked a that type of thing, too. Then the wing nuts spoke to me.

Hoping the other bits finally arrive today so that I can blank off the screw cap / lid. Ordered 7 days ago. Strikes have slowed things up big time.

[floydmeddler]

Progress! Lid is sorted. Have to do a pressure test obvs, but It's looking good.

Since I never have to open this little unit again, is there any way I can glue it together. More than anything, I feel this will add strength to it. Is there a suitable glue out there? I'm pretty sure its polypropylene or polyethylene.

IMG_7751.jpg (1.14 MiB) Viewed 8718 times

IMG_7752.jpg (1.01 MiB) Viewed 8718 times

IMG_7753.jpg (856.03 KiB) Viewed 8718 times

IMG_7754.jpg (996.09 KiB) Viewed 8718 times

IMG_7755.jpg (725.08 KiB) Viewed 8718 times

[MashBag]

If you don't open it how will you clean it?