Inkbird ITC-308S Problem(s)
- MarkA
- Lost in an Alcoholic Haze
- Posts: 678
- Joined: Fri Mar 14, 2014 11:26 am
- Location: Aberdeenshire
Inkbird ITC-308S Problem(s)
I've posted before about problems I've had with my Inkbird temp controller, but this time it's gone too far! I've put up with having to recalibrate it on a far too regular basis, temps jumping about all over the place etc
I made a brew on Friday and tucked it away in the fridge with the Inkbird set at 20 degrees. It's been fine all weekend until this morning when I looked and it was reading the wort as -4. The fridge isn't even plugged in (due to the endless jumping about of temp and the fridge cycling on and off) and when I checked the temp of the wort, it read 35 degrees!! WTF???
It's time for the bin unless anyone has any suggestions? Maybe it's the temp probe that's knackered? If so, are there any other makes of better quality that would fit?
Oh, and the yeast was Mangrove Jacks Liberty Bell, so it'll be interesting to see how that turns out!
Cheers
I made a brew on Friday and tucked it away in the fridge with the Inkbird set at 20 degrees. It's been fine all weekend until this morning when I looked and it was reading the wort as -4. The fridge isn't even plugged in (due to the endless jumping about of temp and the fridge cycling on and off) and when I checked the temp of the wort, it read 35 degrees!! WTF???
It's time for the bin unless anyone has any suggestions? Maybe it's the temp probe that's knackered? If so, are there any other makes of better quality that would fit?
Oh, and the yeast was Mangrove Jacks Liberty Bell, so it'll be interesting to see how that turns out!
Cheers
Re: Inkbird ITC-308S Problem(s)
Sounds like it’s faulty. How long have you had it? Passed the 12 month warranty, knowing Sod’s Law. I’d replace the NTC probe to test it. Cheapest option.
- MarkA
- Lost in an Alcoholic Haze
- Posts: 678
- Joined: Fri Mar 14, 2014 11:26 am
- Location: Aberdeenshire
Re: Inkbird ITC-308S Problem(s)
I think I've had it about 8 years, so slightly out of warranty! I guess it's not done bad, though has had issues metioned above along the way.
I've got a longer probe on order so will see if it's any better, cheers.
-
- Even further under the Table
- Posts: 2681
- Joined: Mon Mar 22, 2010 7:10 pm
- Location: Christchurch, Dorset
Re: Inkbird ITC-308S Problem(s)
Not sure about this, but I vaguely remember something about older Inkbirds having this problem. Don't know if it was the probe or the electronics.
Mine are about 4 years old and are problem free.
Perhaps a new one is the way to go.
Best of luck!
Guy
Mine are about 4 years old and are problem free.
Perhaps a new one is the way to go.
Best of luck!
Guy
- MarkA
- Lost in an Alcoholic Haze
- Posts: 678
- Joined: Fri Mar 14, 2014 11:26 am
- Location: Aberdeenshire
Re: Inkbird ITC-308S Problem(s)
Cheers Guy, I think you're right but nothing to lose in trying a new probe. If all else fails, I'll have a newer Inkbird and a spare probe as a back-up
-
- Even further under the Table
- Posts: 2681
- Joined: Mon Mar 22, 2010 7:10 pm
- Location: Christchurch, Dorset
Re: Inkbird ITC-308S Problem(s)
Just looked at the two Inkbirds I have. Neither has a detachable probe.
Does yours, or will you need to cut the cable or get inside the case to replace it?
Guy
Does yours, or will you need to cut the cable or get inside the case to replace it?
Guy
- MarkA
- Lost in an Alcoholic Haze
- Posts: 678
- Joined: Fri Mar 14, 2014 11:26 am
- Location: Aberdeenshire
Re: Inkbird ITC-308S Problem(s)
Mine's got a detachable probe, it looks the same as a headphone socket and plug so easy to swap
- MarkA
- Lost in an Alcoholic Haze
- Posts: 678
- Joined: Fri Mar 14, 2014 11:26 am
- Location: Aberdeenshire
Re: Inkbird ITC-308S Problem(s)
I got THIS probe from ebay (I made an offer of £8.99 and it was accepted) and it looks like it's working fine now. I've got it stuck in water in the brewfridge and it's consistently reading the same as my Thermapen. I decided on the longer one so the wire join is not sitting in the liquid.
Also, the beer that was fermenting at 35 degrees is now in the bottle and perfectly drinkable, so a happy ending!
Also, the beer that was fermenting at 35 degrees is now in the bottle and perfectly drinkable, so a happy ending!
Re: Inkbird ITC-308S Problem(s)
Excellent news.
Been fiddling recently, and I have come to the conclusion "any doubt replace the probe". Works like a charm.
Been fiddling recently, and I have come to the conclusion "any doubt replace the probe". Works like a charm.